- Linux On Windows Subsystem Ubuntu
- Install Macos On Windows Subsystem For Linux Windows 7
- Install Macos On Windows Subsystem For Linux Has No Installed Distributions
- How To Use Windows Subsystem For Linux
May 20, 2020 2020 will be the year of Linux on the Windows desktop. Linux on Windows just took a big graphical desktop step forward with Microsoft's plans for Windows Subsystem for Linux.
-->Install the Windows Subsystem for Linux
Before installing any Linux distributions on Windows, you must enable the 'Windows Subsystem for Linux' optional feature.
Open PowerShell as Administrator and run:
To only install WSL 1, you should now restart your machine and move on to Install your Linux distribution of choice, otherwise wait to restart and move on to update to WSL 2. Read more about Comparing WSL 2 and WSL 1.
Update to WSL 2
To update to WSL 2, you must meet the following criteria:
- Running Windows 10, updated to version 2004, Build 19041 or higher.
- Check your Windows version by selecting the Windows logo key + R, type winver, select OK. (Or enter the
ver
command in Windows Command Prompt). Please update to the latest Windows version if your build is lower than 19041. Get Windows Update Assistant.
Enable the 'Virtual Machine Platform' optional component
Before installing WSL 2, you must enable the 'Virtual Machine Platform' optional feature.
Open PowerShell as Administrator and run:
Restart your machine to complete the WSL install and update to WSL 2.
Set WSL 2 as your default version
Linux On Windows Subsystem Ubuntu
Run the following command in PowerShell to set WSL 2 as the default version when installing a new Linux distribution:
You might see this message after running that command:
WSL 2 requires an update to its kernel component. For information please visit https://aka.ms/wsl2kernel
. Please follow the link (https://aka.ms/wsl2kernel) and install the MSI from that page on our documentation to install a Linux kernel on your machine for WSL 2 to use. Once you have the kernel installed, please run the command again and it should complete successfully without showing the message.Note
The update from WSL 1 to WSL 2 may take several minutes to complete depending on the size of your targeted distribution. If you are running an older (legacy) installation of WSL 1 from Windows 10 Anniversary Update or Creators Update, you may encounter an update error. Follow these instructions to uninstall and remove any legacy distributions.
If
wsl --set-default-version
results as an invalid command, enter wsl --help
. If the --set-default-version
is not listed, it means that your OS doesn't support it and you need to update to version 2004, Build 19041 or higher.Install your Linux distribution of choice
- Open the Microsoft Store and select your favorite Linux distribution.The following links will open the Microsoft store page for each distribution:
- From the distribution's page, select 'Get'.
Set up a new distribution
The first time you launch a newly installed Linux distribution, a console window will open and you'll be asked to wait for a minute or two for files to de-compress and be stored on your PC. All future launches should take less than a second.
You will then need to create a user account and password for your new Linux distribution.
Set your distribution version to WSL 1 or WSL 2
Install Macos On Windows Subsystem For Linux Windows 7
You can check the WSL version assigned to each of the Linux distributions you have installed by opening the PowerShell command line and entering the command (only available in Windows Build 19041 or higher):
wsl -l -v
To set a distribution to be backed by either version of WSL please run:
Make sure to replace
<distribution name>
with the actual name of your distribution and <versionNumber>
with the number '1' or '2'. You can change back to WSL 1 at anytime by running the same command as above but replacing the '2' with a '1'.Additionally, if you want to make WSL 2 your default architecture you can do so with this command:
This will set the version of any new distribution installed to WSL 2.
Install Macos On Windows Subsystem For Linux Has No Installed Distributions
Troubleshooting installation
How To Use Windows Subsystem For Linux
Below are related errors and suggested fixes. Refer to the WSL troubleshooting page for other common errors and their solutions.
- Installation failed with error 0x80070003
- The Windows Subsystem for Linux only runs on your system drive (usually this is your
C:
drive). Make sure that distributions are stored on your system drive: - Open Settings -> Storage -> More Storage Settings: Change where new content is saved
- The Windows Subsystem for Linux only runs on your system drive (usually this is your
- WslRegisterDistribution failed with error 0x8007019e
- The Windows Subsystem for Linux optional component is not enabled:
- Open Control Panel -> Programs and Features -> Turn Windows Feature on or off -> Check Windows Subsystem for Linux or using the PowerShell cmdlet mentioned at the beginning of this article.
- Installation failed with error 0x80070003 or error 0x80370102
- Please make sure that virtualization is enabled inside of your computer's BIOS. The instructions on how to do this will vary from computer to computer, and will most likely be under CPU related options.
- Error when trying to upgrade:
Invalid command line option: wsl --set-version Ubuntu 2
- Please make sure that you have the Windows Subsystem for Linux enabled, and that you're using Windows Build version 19041 or higher. To enable WSL run this command in a PowerShell prompt with admin privileges:
Enable-WindowsOptionalFeature -Online -FeatureName Microsoft-Windows-Subsystem-Linux
. You can find the full WSL install instructions here.
- Please make sure that you have the Windows Subsystem for Linux enabled, and that you're using Windows Build version 19041 or higher. To enable WSL run this command in a PowerShell prompt with admin privileges:
- The requested operation could not be completed due to a virtual disk system limitation. Virtual hard disk files must be uncompressed and unencrypted and must not be sparse.
- Please check WSL GitHub thread #4103 where this issue is being tracked for updated information.
- The term 'wsl' is not recognized as the name of a cmdlet, function, script file, or operable program.
- Ensure that the Windows Subsystem for Linux Optional Component is installed. Additionally, if you are using an ARM64 device and running this command from PowerShell, you will receive this error. Instead run
wsl.exe
from PowerShell Core, or Command Prompt.
- Ensure that the Windows Subsystem for Linux Optional Component is installed. Additionally, if you are using an ARM64 device and running this command from PowerShell, you will receive this error. Instead run